The 'survival cell' has minimum external dimensions to ensure that
the drivers are adequately protected, whilst the cockpit opening is
heavily regulated, ensuring that all of the teams' designs are the same,
acting as a further control measure in the event of an accident and
allowing swift departure by the driver from the car.
Since 1988, the drivers' feet have been required to be behind the
front wheel centreline, following several accidents that had resulted in
broken legs in the preceding seasons.
This resulted in a dramatic change in the driving position, with
drivers' feet raised, which is in sharp contrast to the ordinary seated
position they'd be used to.
The
wide, sweeping regulation changes for 2014 were accompanied by a change
to the side impact protection spars, which are the first line of
defence in a side on impact.
Following Robert Kubica's huge crash in Montreal in 2007, the FIA in
collaboration with a number of teams conducted additional research into
crash structures when hit at an oblique angle.
It is this research that led to the spars that are currently being
used, the original design of which stemmed from the Marussia team and
was subsequently refined by Red Bull Racing.
The spars are now able to absorb almost 40kJ of energy, in both normal and oblique impact directions.
The standardisation of these side impact spars has seen many teams
resorting to creating blisters on their sidepods shoulders [see Mercedes
above], in order that they house the spars but improve aero in quite a
sensitive area.
In 2007, the FIA introduced measures which required the teams to
flank the cockpit with Zylon strips, Zylon is used in bulletproof vests
owing to its remarkable tensile strength.
The FIA earmarked the material as a way of further protecting the
driver from ballistic shards that could otherwise penetrate the cockpit.
The Zylon is mounted around the inner edge of the cockpit template,
the height of which was increased by 20mm for 2016, whilst the load test
was increased from 15kn to 50kn.
You'll often hear reference to a 'seat fitting' on the lead-up to any
F1 season - this is when a driver goes to the factory to have their
seat prepared for the upcoming season.
During the seat fitting, they will sit on a bag inside the cockpit,
which is filled with a resin that, once dry, forms the negative mould
for the carbon layup. The finished seat is a lightweight carbon fibre
construction that can be easily removed from the cockpit along with the
driver if they cannot exit of their own accord.
The seat is held to the chassis with two bolts, which can be released using a standard tool, issued to all rescue crews. Although
it seems almost unthinkable now, the six point harness that holds the
driver to this removable seat only became mandatory in 1972.
The seat has further straps attached to it in case the driver needs
to be extricated, whilst a slot is added to the upper surface so that a
stabilizer can be inserted by the medical team to support the driver's
head and neck whilst they are removed from the car.
The monocoque has two roll structures in case of inversion: one ahead
of the steering wheel, atop the chassis [secondary] and one that must
be placed at least 940mm above the reference plane, 30mm behind the
cockpit template [primary].
The triangulation of these two points means the driver's helmet
should never come into contact with the ground, should the car roll
over.
The primary structure is constructed taking into account the airbox, which feeds air to the internal combustion unit.
Great effort is made in order to shape this structure to improve aero
whilst reducing weight. After all, this is the highest point on the car
and has a genuine effect on the cars CoG.
However, the FIA insists that the structure be able to withstand a
load equivalent to 50kN laterally, 60kN longitudinally in a rearward
direction and 90kN vertically, as a failure of this roll hoop would be
catastrophic.
When the HANS device was made mandatory in 2003, after extensive
testing many questioned why it was needed. However, it is now a
ubiquitous item worn by motorsport stars around the world and has likely
saved numerous lives.
The simple device retains the relative position of the head to the
driver's body, transferring energy to the torso as the head is
decelerated.
It is the movement of the head that the FIA is interested in as it
continues to study accidents after the fact, which will be further
helped over the coming years by the introduction of a high-speed camera,
mounted in front of the driver atop the chassis from 2016.
The footage collected from Alonso's crash last weekend could be
invaluable in future safety initiatives and studies undertaken by the
governing body.
In recent months the discussion of additional head protection has come to the fore, with the emergence of the 'Halo'.
Whilst most fans seem to reluctant to see the merits, the FIA, teams
and drivers alike have agreed that head protection will be introduced in
2017.
Whilst we concur that the Halo is not exactly aesthetically pleasing,
it is at least better than some of the initial concepts first tested by
the FIA.
The halo is a stylised version of the hoop first tested by the FIA,
along with many other solutions, in order to deflect large objects, such
as an errant wheel, from impacting with the driver's head.
The Halo used by Ferrari
during pre-season testing was not a structural device and so running
was limited to installation laps, although neither driver complained of
line of sight issues during their short runs whilst it was attached.
The Halo has come in for criticism based on the lack of protection
offered from smaller debris, like the errant spring from Rubens
Barrichello's BGP001 that struck Felipe Massa's helmet in 2009.
Although that was not the express intent of the additional hoop, Red Bull have since weighed in with their own iteration, featuring a windshield and dual A pillars, in order to cover both bases.
Yet it still has its detractors, with most focused on the negatives
rather the benefits of enclosing the driver and shielding them from
debris.
No matter which solution is ultimately chosen by the FIA for use in
2017, it shows that the governing body still strives to make
improvements and heed observations from ongoing incidents.
Subscribe to:
Post Comments (Atom)
0 comments:
Post a Comment